#AUTODESK MEMENTO TUTORIAL HOW TO#
#AUTODESK MEMENTO TUTORIAL ANDROID#
#AUTODESK MEMENTO TUTORIAL DOWNLOAD#

If you were trying to grab one of the other overlapping objects, right-click to cycle to the next part. If it is, you have to left-click again to confirm. In cases like that, EAGLE will pick one of the two overlapping objects, and ask if that's the one you want. Normally, you use the mouse's left-click to select an object (whether it's a trace, via, part, etc.), but when there are two parts overlapping exactly where you're clicking, EAGLE doesn't know which one you want to pick up. Since the board view is entirely two-dimensional, and different layers are bound to overlap, sometimes you have to do some finagling to select an object when there are others on top of it. This is an interface trick that trips a lot of people up.

Here's one last tip before we get to laying our board out. Before you start routing, make sure the layers above (aside from tStop and bStop) are visible. To turn any layer off or on, click the 'Layer Settings.' button - and then click a layer's number to select or de-select it. This might show the outline of a part, or other useful information. These are usually drill holes for stand-offs or for special part requirements. These define where soldermask should not be applied.Ībsent soldermask on the bottom side of the board. Origins for parts on the bottom side of the board. Top origins, which you click to move and manipulate an individual part. Silkscreen printed on the bottom side of the board. Silkscreen printed on the top side of the board. Rubber-band-like lines that show which pads need to be connected. Also indicates copper on both layers.Īirwires. These are usually covered over by soldermask. Smaller copper-filled drill holes used to route a signal from top to bottom side. Any part of the green circle is exposed copper on both top and bottom sides of the board. Here are the layers you'll be working with in the board designer: Color We use a palette of colors to represent the different layers. The EAGLE board designer has layers just like an actual PCB, and they overlap too. The app uses the area around the object to orient the camera’s locations.The layers of a double-sided PCB (image from the PCB Basics tutorial). Remember you must move around the object, do not turn the object itself.

There ought to be enough room to view each angle of the objectįrom there follow the in-app guides to circle the object.

The object should NOT be transparent, translucent or reflective.

The object should be clear of obstructions.

After downloading, open the app and create an account – this step will make it easier to find your catches later for download.įor a successful 3D capture there are a couple things to keep in mind:

#AUTODESK MEMENTO TUTORIAL DOWNLOAD#

Download the one for your smartphone by searching for ‘123D Catch’ in the corresponding marketplace.

#AUTODESK MEMENTO TUTORIAL ANDROID#

The 123D Catch app is available on two different smartphone platforms: in the App Store, in the Android Marketplace. Download the 123D Catch App from Autodesk

Download the 123D Catch App from Autodeskġ.

We’ve broken the process down into 5 Steps

#AUTODESK MEMENTO TUTORIAL HOW TO#

This 123D Catch Tutorial will teach you how to use the 123D Catch Smartphone Application, the 123D Catch PC software, and Sculpteo to create a figurine in Sculpteo’s multicolor material. You can still print the objects you catch using the app, it just takes a few more steps. With the app you can take pictures and generate a 3D model through the cloud without using an additional camera (or even saving all of the pictures on your phone’s camera). However, there is no way to get a 3D print from within the 123D Catch app interface (this is likely because the models usually need additional optimization in order to 3D print).

Can’t make it to our meetup in Paris this weekend with Autodesk? Learn how to use 123D Catch app to get your 3D models printed from anywhere in this tutorial!ġ23D Catch app offers an easy, seamless way to get a 3D scan of any physical object you can imagine.

Autodesk memento tutorial